How to Change the Chargeable Battery of Condor XC-Mini

This is the Power Supply Adapter with Battery for Xhorse Condor XC-Mini key cutting machine. No need to connect Car inverter, battery as power supply, easy to carry out. Support household electricity and cigarette lighter to recharge or use as power supply.

List of rechargeable battery of XC-Mini

① Mainboard 

② Cable of 6 & 7 

③ Battery charger & display module 

④ Vehicle charging line 

⑤ Adaptor 220V


Specification of rechargeable battery of XC-Mini:

Standard voltage 25.9V 

Limited charge voltage 29.4V 

Rated Capacity 2500mAh 

Power Ra 73.5Wh 

Note: The update version Condor XC-Mini Plus with built-in battery is coming soon. Don't need to change chargeable battery any more.

Instruction of how to change the built-in battery of Condor MINI:

Remark: please follow the procedure to operation in case of damage the Mainboard ,do not connect the power during operation

Attention : For your security, do not connect the power in next steps

1 , Take off those 4 screws like the picture show 

2 , Push the motor inside and hold the white buckle then take out the emergency-stop module like the picture show

3 , Loose the connection of position 11 &12 like picture show

4 , Use a screw to make the connection those two cables what are from position 11 & 12 like the picture show ,and use the acetate tape fix the connection well 

5, Fix the cable 6 to the position 12 , cable 7 for position 11 , then put the emergency – stop module back and fix it well

6, Take off those 2 screws like picture show

7, Turn over the Mini Condor and take off the foot rubber and 

8, Take out the Power-board and disconnect all cables like picture show

9, Use the battery charger & display module to replace the original power interface like picture show 

10 , Fix the cable into the socket according the number between the cable and socket ,make sure very cable will be fix well

11, Fix the cable of 24V and cable of GND in the right position like picture show

12, Connection the power like picture show then put back the Mainboard and fix it well

13, Fix the all cables after put back the mainboard , the mainboard should be in fixed very solid ,manage the cables again if not , then fix the foot rubber and screws 

14, Fix those screws like picture show

15 , The screen , LED , display of battery charger should be on after you press the emergency – stop button , if not ,check the connection again

Remark : electricity volume will be show by the green light , the LED that is mark ‘’ CHRG ‘’ should be green if it is charged , it will be red during charging.

http://www.vvdishop.com/wholesale/power-supply-adapter-for-xhorse-condor-xc-mini.html

How to use Condor XC-Mini to Cut HU64

Q:

Need some help cutting HU64.
Today I’ve got my Mini Condor key cutting machine.
How to align the tip of the key?

A:

Put on a glove if you can’t tighten it with bare hand.

Problem solved. The Jaw was not assembled wrong from factory. I open it and put it as it should be.

Q: What is the difference between HU64, 64-2, 64-3 and 64T?

A: M2 tighten HU64 key blank no problem. HU64, HU64-2, HU64-3 the distance from key tip to first bitting is different（580,450,380）1mm=100.
such as Mercedes HU64 because different country with different HU64 types, so Xhorse added 3 types from all customers.
so for add spare key, when decode key customer can check the probe detection points whether at proper position.
one more thing, we usually try HU64-3 first, in China mostly select HU64-2 for Mercedes.

The distance from the tip of the key, to the last cut.
If you are not sure which one to choose, just go for the Hu64-3.

www.vvdishop.com

http://blog.vvdishop.com/cut-key-hu64-using-condor-xc-mini/