How to Solve Xhorse Condor II Error Code 56?

If had an error code 56 problem with your Xhorse Condor xc-mini plus ii key cutting machine, here is a working solution.

 

Error code 56

The cutter is short circuited, check the cutter conductivity.

Solution:

First of all, as the error code indicated check the condor ii conductivity as follows:

How to Check Xhorse Condor XC-Mini Plus II Conductivity?

If none of the cables are broken, you can ignore the conductivity problem.
If the machine shuts off as it’s starting to cut, do the following:

Remove those screws to take off the machine screen

Find out the main board of xhorse condor ii, then remove the resister (marked red in the last image) and short it up.

How to use Xhorse Condor II Universal Key Duplication?

 There’s one more way to decode a key on Xhorse Condor XC-Mini Plus II key cutting machine: that’s through Universal Key Duplication. It does copy the key exactly. This can be used as an alternative method once all keys lost or cut by bitting was unsupported.

 

Today we’re going to use a TOY43 as demonstration, this key does not have a shoulder.

 

Universal key duplication >> Standard double-sided key >> Tip align >> M5-A clamp

It’s suggested to use M5 clamp side A, and put it to the third line.

We’ll just pop the blade in, make sure it’s nice and straight to that third line.

 

Press “Decode key”.

Condor Mini Plus 2 starts decoding automatically…

Universal key decode success.

 

It’s looking pretty spot-on. This key is actually in good condition, so doing it this way will quite well. However, if you can do the all keys lost or cut by bitting method, it’s more highly recommended.

 

Alright now that, we’ve decoded the key.

We’ve got a blank key, so we can continue to put in the same position and start cutting.

www.vvdishop.com

How to Fix Xhorse Dolphin XP007 Workbench Shakes?

 Problem:

My xhorse dolphin xp007 manual key cutting machine workbench shakes and two handles loosen. It will not cut key properly. How to fix it?

Solution:

First of all, follow solution here

http://blog.vvdishop.com/xhorse-dolphin-xp007-cannot-slide-back-and-forth-solution/

If problem still exists, follow instruction below:

I. Workbench shakes

Step 1: Check if the screws are loosened.
If yes, tighten it immediately.

Step 2: Check the gap between 1 (thin-walled bearing) and 2 (shaft).
If the gap is large, the shaft needs to be replaced.

Step 3: Check the limit of 2 axes. Move the workbench to the extreme left to discover this location.
If it is loose, please tighten the 2 limit screws to withstand the limit end of the shaft.

 

II.  Workbench cannot move forward and backward

Step 1: Disassemble the dolphin xp-007 machine

 

Step 2: Check the cross slide and linear guide

Check the sides of the cross slide for scratches and bite marks.
If yes, please use a file to smooth the scratches and bite marks.

Check whether the sliding of the guide rail is stuck.

If there is stagnation, please remove the foreign matter in the gap on both sides of the guide rail, and add guide rail oil.
Still can’t slide after foreign matter is removed. It means that the internal bearing of the guide rail is stuck, and there is a quality problem with the guide rail. Next, proceed to the third step.

 

Tip: In general, the second step can solve the problem that the workbench cannot move forward and backward.

 

 

Step 3: Disassemble the linear guide for repair

Loosen 8 screws
Push the guide rail, push the end face A of the guide rail to the position of the red line, and push the end face B of the guide rail to the position of the yellow line.
If it can be pushed, the foreign matter can be discharged by filling the guide rail with oil until the guide rail slides smoothly.
If the guide rail still cannot be pushed, please restore the device and return it to the factory for repair.

 

www.vvdishop.com

Xhorse Condor II Cut 2022 Ford Maverick HU198T Key

 I’m gonna attempt to cut a 2022 Ford Maverick HU198T key with Xhorse Condor XC-Mini Plus II key cutting machine. I’ll decode it first then cut it.

 

Unfortunately, I can’t find the HU198T option under Maverick, so I’m going to try with Escape HU198T that may work.

Fix on a working key on M5 clamp.

Automotive >> Brand/ model >> Ford >> Escape >> HU198T >> Decode

Key learning success.

It’s 4534343122.

Install a new key blank on M5 clamp.

Starting cutting >> Cut

Side one is done, it looks all right.

We’re gonna see what we end up with one thing: the 20+ Bronco, 20+ Escape and 20+ Maverick. You may have to cut the mill, the tip of this key down if you notice. The 101 is angled over a little bit but let’s try cutting it anyway. And see what happens.

Let’s continue to cut the other side.

Flip over the key blank:

Starting cutting >> Cut

 

Xhorse Condor 2 is a new machine for me, but it does work in ease.

The new key can open the door & switch ignition on well.

Perfect work!

www.vvdishop.com

Xhorse Dolphin II “Check Internet Error” Solution

 Problem:

How can I update my Xhorse Dolphin II XP005L key cutting machine? It keeps giving me the check internet error. Already tried 4 different internet and got nothing.

 

 

Solution:

Customers have tried following and working

1. Try with a PC with Windows 8 max, the upgrade kit didn’t work with windows 10 laptop.

2. I got it to work, I had to connect and disconnect my wifi connection a few times and update it.

 

 

Xhorse engineer solution:

Connect with a mobile hotspot and do an update.

Xhorse Dolphin II Decode VW HU66 Bitting by Photo

 How to decode a Volkswagen HU66 key by photo scanning with Xhorse Dolphin key cutting machine? Following is taking Dolphin XP005L as a demonstration. The procedure can be used to read most key types as well.

 

Xhorse App >> Dolphin >> Take photo to recognize bitting >> Volkswagen >> HU66

Put the key blade horizontal in the fixed area.

Keep key tip on the top.

 

Dolphin II will automatically read each bitting with dots.

Press “OK”.

Bitting codes were read out in seconds.

It’s 11214443.

 

Quickly done.