Question:
I would like to know how to duplicate a sx9 key with Xhorse Dolphin II.
I can’t find the M3 clamp in the machine menu.
Answer:
Don’t need to choose M3 clamp option in settings.
Direct replace M3 clamp when cutting sx9 key (or other tibbe keys)
Read also:
If your Xhorse dolphin xp005l (dolphin ii) key cutting machine does not bring new updates and whenever you update it stucks on screen, you may need to enter developer mode to update firmware.
Here is the guide to enter developer mode.
Go to System
Press the question mark icon on the right top of the screen
Press the QR code
Press Yes to clear all data and enter Developer Mode (factory mode).
Update firmware in Developer mode.
Then switch to normal mode to update firmware again.
It should be fine.
Problem:
I did the first installation but my xhorse dolphin ii key cutter doesn’t decode the keys. Fiat Idea SIP22 blank.
Solution:
You didn’t put the key in the clamp correctly.
Re-adjust the key in the m5 clamp.
The shoulder of the blade is your stop point at the jaw.
This is how you must place the key.
What’s the difference between 2023 new Xhorse dolphin xp005 (without battery version) and old Dolphin XP005 (with battery version)?
1. Without built-in battery. Works with or without battery.
If need battery, you can buy an optional battery for dolphin.
If without battery, you can take out for work by car.
2. Comes with M5 clamp in default (M5= M1+M2)
1.Come with built-in battery. Works only with built-in battey. Cannot work without battery.
2. Old dolphin comes with M1 and M2 clamps in default. Also compatible with M5 clamp (purchase separately.)
Apart from that, they make no difference in appearance and functions.
Problem
Xhorse Condor II key cutting machine had error code 57.
The probe is short-circuited.
Solution
Just as it indicated, the probe is short-circuited.
Follow guides below to disassemble machine
Then check the probe catheter.
Check if it is broken and report result to www.vvdishop.com
Problem: I was going to use Xhorse VVDI Key Tool Max to control Condor XC-Mini Plus & Key Reader for a cutting. But it failed to connect Key Reader all the time. The Bluetooth and power are on.
What’s the problem? Please advise.
.jpg)
.jpg)
.jpg)
Solution
Please connect Key Reader in the key option to be cut:
DO NOT connect in the CondorMini Plus home page, this problem can be solved.
Hope this is helpful.
Good luck.
Technical Support
Since I’ve used the ZD24R LISHI to pick and decode a Can-Am Spyder 3-wheel motocycle ignition, so next I’m going to cut the key with Xhorse Dolphin XP005 by bitting. In case to wreck a pretty expensive key blank, I would try X270 TMC1 key for a test at first. The bitting codes decoded by LISHI is 232234.
.jpg)
.jpg)
Cut by bitting >> Silca – ZD24R >> ZD24R, 6 bitting, 770*2350
M1 clamp Shoulder align.
This type recommend use 1.5mm to cut.
Press “OK”.
Input the bitting codes: 232234
Put and fix the key on M1 clamp according to prompts.
Cut key >> Cut
Dolphin XP005 machine starts cutting automatically.
Please wait…
.jpg)
.jpg)
.jpg)
.jpg)
.jpg)
Get the key out when cutting completed.
It’s working perfectly in ignition.
It should be noted in particular here this Can-Am ignition is from 2011 or 2012, it’s wide open and easy to get the keyway. The key can work with no problem at all.
But some of the newer ones starting like 2019/2020/2021, this black bezel here that actually covers most of this ring. So either have to pop that off or what I like to do is just to cut the head of key off.
When you try to put the key in, it stops on the bow of the key and it won’t go all the way in. So you may think your cuts are wrong. Just cut the whole head of key off, test it and make sure it’s working here before cutting.
This is how to cut ZD24R key with Dolphin successfully, you may use the newer Dolphin II Key Cutting Machine to do the job as well.
.jpg)
.jpg)
.jpg)
